服务热线:400-028-9008
您好!欢迎访问图拉扬公司![登录] [注册]
我的订单

DOPO2光纤氧测定仪,光纤微氧分析仪

检测限低至2ppb
. 电询
产品编号: tlyon005401
产品品牌: 美国FMI
产品指数: 2259
样本资料: 索取
供货周期: 合同约定
关联标签: DOPO2光纤氧测定仪,光纤微氧检测仪,光纤微氧分析仪
数量:

  DOPO2-FIBER OPTICS 是一种电光模块,设计用于连接光纤传感器,用于远程监测溶解氧和气体。它可以与各种不同尺寸的光纤一起使用,从大型现场应用到非常小的(针大小)生物环境。它还具有蓝牙功能和内置 USB 可充电电池。嵌入其中的通讯模块支持

·4-20mA模拟输出

·RS485

·USB

·外部温度传感器接口

·适用于安卓设备的蓝牙   

     DOPO2-FIBER OPTICS 系统应连接到具有嵌入式温度传感器的不同尺寸的光纤氧气探头,从而可以远程监测小空间内的溶解氧。  

      DOPO2-FIBER OPTICS 系统配备可充电内部电池,可从 USB 端口充电,充满电后可运行 8 小时。

      用户可以 通过 USB 将其连接到 PC 并以 Microsoft Excel 格式保存数据,或通过蓝牙将其与 android 设备一起使用并以 CSV 格式保存数据。 

   与 DOpO2-PRO 类似,可配置单通道 LED 激励和检测,调制频率高达 31.2 kHz。

       光纤探头不包含在价格中。

 

原则: 在溶胶-凝胶主体中使用有机金属化合物的光致发光猝灭
测量参数: 气态氧分压、溶解氧浓度、温度、压力(通过板载压力传感器)
   
兼容性: 气体、液体、碳氢化合物、燃料、有机溶剂、油
控制软件: 具有数据记录功能的 Windows 7、8、10 控制软件;控制包括:调制频率、数据速率、信号平均、LED 增益、LED 强度
采样率: 每 1 秒 (1 Hz) 采集数据样本
(软件可以配置为不同的采样率)  
注意:这不是探头的响应速度,只是探头进行数字采样的速率
压力测量: 板载压力传感器监测大气压力
4-20 mA 输出精度(25°C 时): +/- 0.1%
电子工作温度范围: 0°C -55°C
外接电源电压范围: 4.75 至 5.25V
能量消耗: 100毫安
通讯: 通过 Android 应用程序、USB、4-20mA 模拟输出和 RS485 实现无线连接 

 

传感器规格

Response rate (T90)

无涂层。~1秒

黑色涂层。~45秒

在气体中范围

0-100% O2 / 0-760 mmHg O2

在水中动态范围 (DO)

0.002-40 ppm (wt.)

在其它液体中

0-饱和氧水平

分辨率(在气体中)

0.005% O2 / 0.04 mmHg

分辨率在水中 (DO)

0.002 ppm (wt.) / 2.0 ppb (wt.)

分辨率在其它液体中

0.005%-饱和氧范围

准确性

读数5%

在气体中检测限LOD

0.005% O2 / 0.04 mmHg

在水中动态检测限(DO)LOD

0.002 ppm (wt.) / 2.0 ppb (wt.)

在其它液体中检测限LOD

0.005%-饱和氧范围

传感器在空气中的飘逸

0.002% O2 每天

工作温度

0-70℃

质保

一年

应用

FMI 传感器可用于研究、医疗服务、工业等领域的各种应用

环境监测

溶解氧(DO)是影响水产养殖中鱼虾健康生长的关键参数。因此,在线监测水生环境中的溶解氧含量非常重要。此外,为了污水处理厂的高效运行,对溶解氧进行持续可靠的监测至关重要。

FMI溶解氧计(DOPO2)可与各种AP系列传感器产品配合使用,在不同环境应用中监测溶解氧。

·废水管理

·水产养殖监控系统

·地下水溶解氧监测

·空气质量控制

 

生物学

光纤传感是传感领域中一个相对较新的维度,光纤传感器在生物环境中的性能分析在很大程度上仍需要大量深入的研究。

FMI 氧气计 (DOPO2) 可与各种 AP 系列传感器产品一起使用,从浸入式探头、可更换盖帽到针式探头,以监测不同生物环境中的溶解氧。

·土壤呼吸

·海洋科学

 

生命科学

FMI 氧气计 (DOPO2) 可与各种 AP 系列传感器产品一起使用,从浸入式探头、可更换盖帽到 250 um 针式探头,以监测不同生命科学应用中的溶解氧。

·医疗的

·制药

·生物反应器和细胞培养

生物反应器中的氧传感器:我们的氧传感器已被南佛罗里达大学的一个研究小组用于监测大肠杆菌在生长过程中培养液中的溶解氧。 

 

化学工业

FMI 氧气变送器 (DOPO2) 可与各种 HCR 系列传感器产品一起使用,从浸入式探头到可更换的盖子,以持续监测有机溶剂、聚合物和单体中的溶解氧,...

·聚合物和单体 (例如甲基丙烯酸甲酯) 

·有机溶剂(例如甲苯、BTX) 

 

我们的 HCR 系列传感器在浸入 丙酮、甲苯和苯等不同溶剂中时的兼容性和稳定性经过测试和证明这里.

我们的 HCR 系列探头已经过 MMA测试

我们的 HCR 系列探头已经过 HexTD测试

 

石油和天然气工业

·石油 和燃料

·煤油

管道:保护加压天然气管道系统免受泄漏和腐蚀以及最大​​限度地减少停机时间是石油和天然气公司最重要的职责之一。如果样气中存在氧气 (O 2 ),则意味着加压管道系统中存在泄漏。如果这种泄漏仍未被发现,问题可能会恶化并继续影响管道的运行效率。另外,如果管道内的气体样本含有硫化氢(H 2 S)和二氧化碳(CO 2),所有 3 种气体可以结合并形成极具腐蚀性和破坏性的混合物,可以从内到外恶化壁厚。除非进行处理,否则这种腐蚀会继续蔓延,造成更多损害,并缩短管道的使用寿命。最终,损坏会达到存在破裂或潜在爆炸的重大风险的程度。

炼油厂: 连续可燃气体和有毒气体监测是炼油厂运营的一个关键方面。炼油厂中有许多工艺和特殊生产单元会产生特定的安全隐患。

 

航天工业

FMI 氧气变送器 (DOPO2) 可与各种 HCR 系列传感器产品一起使用,从浸入式探头到可更换盖,以监测煤油基喷气燃料中的溶解氧。

·喷气燃料是一种传统的航空燃料,基于 无铅煤油 (Jet A-1) 或 石脑油-煤油 混合物 (Jet B)。与 柴油类似,它可用于 压燃式发动机 或 涡轮发动机。 煤油基燃料的闪点比汽油基燃料高得多,这意味着它需要更高的温度才能点燃。 

·喷气燃料监测

·航空航天生命支持:机载氧气发生系统 (OBOGS) 和 OBIGS

展示了浸入煤油中时 HCR 氧传感器的兼容性、灵敏度和稳定性。煤油被用作代表性介质,因为它同时含有芳香烃和脂肪烃。确定了 HCR 氧传感器的一些关键特性,包括在烃基燃料中的长期稳定性、热循环稳定性、响应速率和对燃料中氧气变化的响应

 

食品和饮料行业

在发酵过程中监测氧气含量非常重要。检查食品包装的气密性和质量也很重要。

FMI 氧气计 (DOPO2) 可与各种 AP 系列贴片一起使用,以无创监测食品和饮料行业中的溶解氧。 

·酿造:为实现长货架期和始终如一的质量和高效生产,FMI 溶解氧传感器可用于发酵、陈化罐、过滤和包装

·饮料:水是任何 饮料的主要成分之一。FMI溶解氧传感器可用于饮料的充气。

 

印刷业

紫外线固化油墨通过紫外线辐射固化并粘附到介质或基材上。打印件从打印机出来时已经干燥,可以满足短期交付要求。 我们的 HCR 传感器已通过 UV 固化油墨的兼容性和稳定性测试

 

气调包装 (MAP)

气调包装也称为气体冲洗或减氧包装。它使食品包装能够延长保质期,而无需添加化学防腐剂或稳定剂。

FMI 氧气传感器可用于无损监测商业包装的MAP食品中的氧气含量。

 

出版物:

1.“Performance evaluation of fiber optical oxygen sensor in bio-reactor with live bacterial culture” Roha Afzal, Pritha Nanda, Newton King, Tunan Peng, Anna Pyayt, and Mahmoud Shahriari, University of South Florida, Chemical and Biomedical Engineering,  poster presentation, April 2013

2.“Effect of salinity and ionic strength on sol gel based fiber optic pH sensors” M.R. Shahriari, Harrish Dabhi, Derek Guenther, In preparation for J. Sol-gel Science and Technology

3.“Smart Oxygen Cuvette for optical monitoring of Dissolved oxygen in biological blood samples”, Harish Dabhi, Suresh Kumar Alla, Mahmoud R. Shahriari,  Proc. of SPIE Vol. 7576  75761B-1 (2010)

4.“Smart pH Cuvette for optical monitoring of pH of biological samples” Derek A. Guenther, Mahmoud R. Shahriari, Proc. of SPIE Vol. 7576  75761A-1 (2010)

5.“Nanoporous thin film platform for biophotonic sensors” Suresh Alla, Rina Solanki, Yvette D. Mattley, Harish Dabhi, Mahmoud R. Shahriari, Proc. SPIE, Vol. 7173, 717304 (2009)

6.“Applying Fiber – Optic Sensors for Monitoring Dissolved Oxygen,” W. Wang, C.E. Reimers, M.R. Shahriari and M. J. Morris, Sea technology, March 1999

7.“A Fiber Optic Sensor for Monitoring the Variability of Dissolved Oxygen in the Coastal Zone,” W. Wang, C.E. Reimers, M.R. Shahriari and S.C. Wainright, The Marine Technology Society Annual Conference Proceedings, Vol. 1 ( 1998)

8. A Sol-Gel Based Fiber Optic Sensor for Monitoring Dissolved Oxygen in Marine Environments,” C.E. Reimers, M.R. Shahriari, S.C. Wainright, W. Wang, Marc’h Mor workshop, IUEM Brest, France, 17-19 November 97, Proceedings

9. “A Spectroscopic Study of the Effect of Various Solvents and Sol-Gel Hosts on the Chemical and Photochemical Properties of Thionin and Nile Blue Red A,” M. Krihak , M. T. Murtagh, and M.R. Shahriari, J. Sol-gel Science and Technology, Vol. 10-2, 153-163( 1997)

10. “ Ormosil Thin Films for Chemical Sensing Platforms,” M.R. Shahriari, M.T. murtagh, H.C. Kwon, Chemical, Biochemical and Environmental Fiber Sensors IX, Proc. SPIE Vol. 3105, pp 40-51 (1997)

11. Fiber Optic Oxygen Sensors Based on the Sol-gel Coating Technique,” M. Krihak, M. Murtagh and M.R. Shahriari, Chemical, Biochemical and Environmental Fiber Sensors VIII, Proc. SPIE  Vol. 2836, pp 87-98 (1996).

12. “Luminescence Decay Analysis of Doped Sol-gel Films,” M. Murtagh, M. Krihak, H.C. Kwon and M.R. Shahriari, Chemical, Biochemical and Environmental Fiber Sensors VIII, Proc. SPIE  Vol. 2836, (1996).

13. “Development of a Highly Sensitive Fiber Optic O2/DO  Sensor  Based on a Phase Modulation Technique,” M.T. Murtagh, D.E. Ackley, and M.R. Shahriari, Electronics Letters, Vol. 32, No. 5  (1996) 477

14. A Highly Sensitive, All Solid State Fiber Optic Oxygen Sensor Based on the Sol-gel Coating Technique,” M. Krihaks and M.R. Shahriari, Electronics Letters, Vol. 32 Number 3 (1996) 240.

15. The Effect of MTMS on the Optical Properties of TEOS Synthesized Gels Doped with Thionin,î ,” M. Krihaks and M.R. Shahriari,  J. Optical Materials,  5, 301-310 (1996)

16. Fiber Optic Chemical/Environmental Sensors based on Active Coatingsî M. Krihaks and M.R. Shahriari, Chemical, Biochemical and Environmental Fiber Sensors VII, Proc. SPIE  Vol. 2508, pp 358-367 (1995).

17.“New Highly Stabilized AlF3-Based Glasses,”  T. Iqbals, M.R. Shahriari, G. Weitzs, G.H. Sigel Jr.,  J. Non-crystaline Solids,  Vol. 184 (1995) 190-193

18.“Active Sol-gel Materials for Fiber Optic Chemical Sensors,” M. Krihaks and M.R. Shahriari, Imaging and Instrumentation, Chemical, Biochemical and Environmental Fiber Optic Sensors, Proc. SPIE, Vol. 2293, pp 88-93 (1994).

19. “Fiber Optic Chemical Sensors for Process Control” M.R. Shahriari, , Proceeding of the Conference on Computer integrated Manufacturing in the Process Industries, Rutgers University,   338-350,  April 1994.

20. “Active Silica Gel Films for Hydrogen Sulfide Optical Sensor Application,” M.R. Shahriari and J. Dings,  Optics Letters, Vol. 19, No. 14 (1994 ).

21.“Optical Properties of AlF3-based Glasses Doped with Pr3+, Yb3+ and Lu3+,” T.  qbals, M.R. Shahriari, P. Hajcaks  G.H. Sigel, Jr., L.R. Copeland and W.A. Reed, Applied Optics, Vol. 33, No. 6, 965-968 (1994)

22. “Sol-gel Coating -based Fiber Optic O2/DO sensor,” M.R. Shahriari, J.Y. Dings, J.Tongs, G.H. Sigel, International Symposium on Optical Tools for manufacturing and Advanced Automation, Chemical, Biomedical, and Environmental Fiber Sensors, Proc. SPIE,  V0l. 2068 (1993).

23.“The Effect of Rare Earth Ions on the Thermal Stability of AlF3-Based Glasses,” M.R. Shahriari, T.  Iqbals, P. Hajcaks  and  G.H. Sigel, Jr., J. Non-crystaline Solids,  161, 77-80 (1993)

24.“Ruggedized Fiber Optic Environmental Sensors Based on Porous Optical Materials,” M.R. Shahriari, J. Lius, G. H. Sigel, Jr., M. Livas, Symposium Proceedings of Field Screening Methods for Hazardous Waste Site Investigations, 3rd International Symposium, Las Vegas, NV, February( 1993).

25. “Development of Porous Polymer pH Optrode,” J.N. Lius, M.R. Shahriari, and G.H. Sigel, Jr., Optics Letters, Vol. 17, No. 24, 1815-1817(1992)

26.“Synthesis f Dye-Impregnated Sol-Gel Glasses for Fiber Optic Chemical Sensing,” J. Dings, J. Tongs, M.R. Shahriari, and G.H. Sigel, Jr., SPIE Proceeding Vol. 1761, Properties and Characterizations of Optical Glasses (1992)

27. “Preliminary Study of Fiber Drawing of AlF3-based Glasses,” T. Iqbals, M.R. Shahriari, P. Foys and G.H. Sigel, Jr., Materials Science and Engineering, B12, 299-303, 1992

28. “Environmental Effects on the Mechanical Properties of Aluminum Fluoride Glass Optical Fibers,” J. Colaizzi, M.J. Matthewson, M.R. Shahriari, T. Iqbal, Ceramic Transactions, Vol. 28, solid state optical materials (1992), pp.579-586

29. “Luminescent Properties of Rare-Earth Doped Aluminum Fluoride Based Glasses,”  M.R. Shahriari, T. Iqbals, P.A. Hajcaks, G.H. Sigel, Jr., and R. Copeland and W.A. Reed, AT&T Bell Labs., Materials Research Society (MRS) Proceeding, Optical Waveguide Symposium, Vol. 244, 203-208, 1992

30. “Sol-Gel and RF Sputtering Thin Film Coatings for Fiber Optic Sensor Applications,”  M.R. Shahriari, J.Y. Dings, C.M. Wangs, C.H. Lins and G.H. Sigel, Jr., Materials Research Society (MRS) Proceeding, Optical Waveguide Symposium, Vol. 244, 287-292, 1992

31. “Porous Fiber OPtical Sensors for pH Measurement,” J.Y. Ding, M.R. Shahriari, and G.H. Sigel, Jr., Optical Fiber Sensor (OFS) conference proceeding, 8th OFS conf., IEEE catalog # 92CH3107-0, pp. 321-324, Jan. 1992.

32. “Effect of Processing on the Optical Scattering of AlF3-Based Glasses,” T.Iqbal, M.R. Shahriari, G.H. Sigel, Jr., A.E. Neeves, W.A. Reed, AT&T Bell Labs., Journal of Materials Research, Vol.7, No.1, 1-5, 1992

33. “Remote Infrared Chemical Sensing Using Highly Durable AlF3-Based Glass Fibers,”  T. Iqbals, M.R. Shahriari and G.H. Sigel, Jr., Optics Letters, Vol. 16, No. 20, 1-3, 1991.

34.“Mechanical Properties of Aluminum Fluoride Glass Fibers,” J. Colaizzi, M. J. Matthewson, T. Iqbal and M.R. Shahriari, SPIE Proceeding, Infrared Fiber OpticsIII, Vol. 1591 (1991).

35. “Fiber Optic pH Sensors Prepared by a Sol-Gel Immobilization Technique,” J. Dings, M.R. Shahriari, and G.H. Sigel, Jr., Electronics Letters, Vol. 27, No. 17, 1560-1562, 1991.

36. “Aluminum Fluoride Based Fibers with Enhanced Optical Transmission,”  T. Iqbals, M.R. Shahriari, P. Foys, R. Ulbrichs, G.H. Sigel, Jr., Electronics Letters, Vol. 27, No.2, 110-111, 1991.

37. “Development of High Temperature Humidity Sensors Based on Porous Optical Fibers,”  J. Y. Dings, M.R. Shahriari, and G.H. Sigel, Jr., International Journal of Optoelectronics, Vol.5. No. 4. 385-393, 1991

38. “Synthesis, Characterization and Potential Application of Highly Chemically Durable Glasses Based on AlF3,” T. Iqbals, M.R. Shahriari, G. Merbergs and G.H. Sigel, Jr., Journal of Materials Research, Vol.6, No. 2, 401-406, Feb. 1991

39. “Chemical Sensors for Hazardous Waste Monitoring,” M.B.Tabaccos, K. Rosenblums, Q. Zhous, and M.R. Shahriari, Symposium Proceedings of Field Screening Methods for Hazardous Waste Site Investigations, 2nd International Symposium, Las Vegas, NV, February 1991.

40. “Fiber Optic Moisture Sensors for High Temperatures,” J. Dings, M.R. Shahriari and G.H. Sigel, Jr., Amer. Ceram. Soc. Bull., Vol.70, No.9,  1513-1517,  1991.

 

*本产品非医疗器械,不能用于临床诊断和治疗,仅科研用途!*
典型用户(近期成交订单数量:0)
还未添加典型用户
用户咨询 (共0条)
  • 如您有留言我们会及时回复,也可通过在线客服或400-028-9008联系我们!

验证码